This item may need to be sourced from Germany and would take 2-4 weeks to arrive. Once ordered it cannot be canceled. Please call to check stock or request expedited shipping.

7 liter engines with air pump

Mechanical pencil in matte and glossy chrome finish is based on the Porsche 911 design. . Twist mechanism. Integrated eraser. Spring-loaded clip. Brass. Dimensions: 5.75 x .5 inches

General Fitment

Agency power is proud to release its super sport exhaust system for the 958 Porsche Cayenne s v8 2011 and up. the super sport exhaust is a axle system that gives your 4.8l v8 engine a real aggressive tone. made here in the usa, the exhaust saves close to 30lbs off the rear end of the vehicle. using 304 stainless steel and detail oriented tig welding, the exhaust system uses two small high flow mufflers which give it the sports car rumble. its reduced back pressure design gives the engine improved horsepower and torque with most noticeable improvement in throttle response. because of the reduced restriction, this exhaust horsepower gains can definitely be noticed in the mid to top rpm range.

Even though ...(choose a part on the right to read more)

0, 2 2, and 2 4 liter engines

The best manuals you can purchase for your Porsche, these concise books show everything to make repairs simple and accurate with easy to follow German logic! They may seem expensive, but if it saves you one repair trip to the Porsche dealer, they have paid for themselves! Note: turbo manuals are supplements to be added to the complete sets.

36 mm open end, long thin spanner wrench (8 mm thickness). Spanner overall length 20 inches. Please call our office for availability.

General Fitment

36 mm open end, long thin spanner wrench (8 mm thickness). Spanner overall length 20 inches. Please call our office for availability.

General Fitment

The wrench is flat and wide and was designed to hold a tensioner pulley in place while the retaining nut is applied. The retaining-nut usually over hangs its base therefore the wrench has to be flat. No conventionally sold metric key-wrench will clear the base for the retaining-nut installation. Do not look for something else. It was tried before you. It just will not clear. Two types of tensioner pulleys are used in 924-944 today. The metal tensioner pulley and the plastic tentioner pulley.

Genuine part # 000 721 911 00. We source this part at Porsche ag in Germany to ensure quality, reliability and precise fitment. Sold individually.

This item may need to be sourced from Germany and would take 2-4 weeks to arrive. Once ordered it cannot be canceled. Please call to check stock or request expedited shipping.

This item may need to be sourced from Germany and would take 2-4 weeks to arrive. Once ordered it cannot be canceled. Please call to check stock or request expedited shipping.

The perfect complement for a numeric racing cable installation. This wrench simplifies installation for numeric racing cables with part # FVD424049 , FVD424050 , FVD424051 or FVD424052 please note: please check the model fitment tab to ensure accurate fitment.

This item may need to be sourced from Germany and would take 2-4 weeks to arrive. Once ordered it cannot be canceled. Please call to check stock or request expedited shipping.

The stock exhaust of the Porsche 997.2 turbo is very restrictive compared to aftermarket systems. Porsche does this to meet sound and emission purposes like most OEM manufacturers. agency power set out to create an exhaust system for the new Porsche 997.2 turbo 6speed or pdk that did not drone, would produced amazing performance, and under throttle give an incredible sound. we have accomplished this! the new agency power exhaust not only saves about 30lbs off the rear end, it also improves power quite a bit.

With our single can muffler and 200cell high flow cats installed to the stock huge oval tips, we strapped our 2010 pdk to the dyno. The exhaust made a peak increase in standard mode of 15awhp and 23f...(choose a part on the right to read more)

This item may need to be sourced from Germany and would take 2-4 weeks to arrive. Once ordered it cannot be canceled. Please call to check stock or request expedited shipping.

Standard valve springs reach only 85 kg. FVD-motorsport-springs have up to 105 kg! The desired value for race-engines is max. 104 kg! The electronic spring scales is recommended to check the spring force. That is a need for optimally calculation of the valve spring mounting-lengths.example: length with 104 kg + lifting = mounting-length of the valve-spring.

This item may need to be sourced from Germany and would take 2-4 weeks to arrive. Once ordered it cannot be canceled. Please call to check stock or request expedited shipping.